INSTITUTE

Reopening an old road between the Nordics and the Gulf.

INDEPENDENCE The NordGulf Institute is fully independent. It publishes its work free of charge, and none of it is commissioned or paid for by any client, government or other institution. It is funded by NordGulf Alliance and its partners, and what it publishes is decided by the Institute alone.

Steel and metals: UAE tariffs on Canadian goods under the CEPA

A NordGulf Institute publication

The UAE charges 5% on most Canadian metals today and 10% on steel bars and rods. Under the Canada-UAE trade agreement (the CEPA), signed on 27 October 2026 and not yet in force, 244 of the 527 tariff lines for iron, steel, copper, nickel and aluminium become duty free on the day the agreement takes effect. Another 237 lines, almost all of them steel products, are marked with an asterisk in the UAE's list. For those, the UAE cuts nothing until Canada tells the UAE that it has removed its own surtax on UAE goods.
Last checked 22 November 2026

Key facts

Tariff lines covered on this page
527 lines in HS Chapters 72 to 76: iron and steel, steel articles, copper, nickel and aluminium
UAE duty today
5% on 480 lines. 10% on 47 lines, almost all steel bars and rods
Duty free from day one, no conditions
244 lines, including scrap, ferro-alloys, hot-rolled coil, copper cathodes, unwrought nickel and most aluminium products
Asterisk lines (cuts on hold)
237 lines: 112 in iron and steel, 123 in steel articles and 2 for unwrought aluminium
What ends the hold
A written notice from Canada that it no longer keeps a surtax on UAE goods under those lines. Cuts start 30 days later
Phased lines without an asterisk
7 lines over four years and 29 lines over six years, mostly copper, nickel and aluminium goods and oil and gas pipe
Left out of the agreement
10 lines of steel articles, including screws, bolts, nuts and helical springs. They keep the UAE's general duty, 5% today
Main origin test
For most metals, an imported input must have a different four-digit tariff code (heading) from the finished product
Status
Signed 27 October 2026. Not yet in force

01What the UAE charges on metals today

Most Canadian metal products pay 5% duty when they enter the UAE today. Steel bars and rods, the kind used to reinforce concrete and in engineering, pay 10%.

  • The UAE is a federation of seven emirates with one customs tariff. The same duty applies whether goods land in Dubai, Abu Dhabi or any other emirate.
  • The agreement uses a "base rate" for every product. This is the duty the UAE charged all trading partners on 1 January 2025. All cuts are measured from it.
  • Every product has an eight-digit code in the UAE tariff. Each code is called a tariff line. The first two digits of a code give its chapter, the first four its heading and the first six its subheading. The more digits, the narrower the product group. This page covers the 527 lines in Chapters 72 to 76 of the Harmonized System (HS), the worldwide product coding system.
  • No metal line in these chapters is free of duty today.
  • Duty is charged on the customs value of the goods (the value of the shipment as assessed by customs). The agreement changes customs duty only. It does not change the UAE's value added tax.
HS chapterWhat it coversLinesDuty today
72Iron and steel in primary and rolled forms1955% on 148 lines. 10% on 47 lines, almost all bars and rods
73Articles of iron or steel: pipes, structures, tanks, wire, fasteners, household goods1825%
74Copper and copper articles595%
75Nickel and nickel articles235%
76Aluminium and aluminium articles685%
  • The 10% lines are in headings 72.13, 72.14, 72.15, 72.27 and 72.28. They cover hot-rolled, forged and cold-finished bars and rods of non-alloy and alloy steel, plus alloy steel angles and sections and hollow drill bars.
  • If the UAE's general duty on a product ever falls below the CEPA rate, Canadian goods get the lower of the two.

02How the cuts are staged

Each tariff line has a letter. The letter says how fast the UAE removes the duty. For metals, 440 lines are in the fastest group, but 196 of those carry an asterisk that puts the cut on hold.

CategoryWhat the UAE doesTariff linesReaches zero
ADuty free from the day the agreement takes effect440Day one
BCut in four equal yearly steps481 January of year four
CCut in six equal yearly steps291 January of year six
ELeft out. The UAE makes no promise. Its general duty or ban applies10Does not reach zero
  • Category A without an asterisk: 244 lines. These are free from day one with no further condition.
  • Category A with an asterisk (A*): 196 lines. On hold.
  • Category B without an asterisk: 7 lines. Category B with an asterisk (B*): 41 lines, all of them in steel.
  • Category C: 29 lines, none with an asterisk.
  • There are no category D lines in metals.

How the yearly steps work

  • Year one starts on the day the agreement takes effect and ends on 31 December of that year. The first cut applies from that first day.
  • Every later cut falls on 1 January.
  • If the agreement takes effect during 2027, category B lines reach zero on 1 January 2030 and category C lines on 1 January 2032. The date of entry into force (the day the agreement takes effect) is not yet fixed.
  • From a 5% starting duty, the four-step path works out at 3.7%, 2.5%, 1.2% and zero. The six-step path is 4.1%, 3.3%, 2.5%, 1.6%, 0.8% and zero.
  • From a 10% starting duty, the four-step path is 7.5%, 5%, 2.5% and zero.
  • These yearly rates are our own arithmetic from the formula in the agreement, rounded down to one decimal place as the agreement allows. The agreement prints only the starting duty and the category for each line.

03Metals that are duty free from day one

Steel-making inputs, hot-rolled flat steel, most copper and nickel, and most aluminium products other than raw ingot enter the UAE duty free from the day the agreement takes effect. The goods must qualify as Canadian under the origin rules in section 07.

  • Iron and steel (Chapter 72): every line in headings 72.01 to 72.08 is in category A with no asterisk. That covers pig iron, ferro-alloys, scrap, ingots, semi-finished steel and hot-rolled flat products.
  • Copper (Chapter 74): 46 of 59 lines.
  • Nickel (Chapter 75): 17 of 23 lines.
  • Aluminium (Chapter 76): 54 of 68 lines, including scrap, powders, most bars and profiles, plate and sheet, foil, and doors and windows.
ProductUAE tariff codeDuty todayCategoryWhat happens
Ferro-manganese with more than 2% carbon7202.11.005%AFree from day one
Iron and steel scrap, other kinds7204.49.005%AFree from day one
Semi-finished non-alloy steel (billets of square or near-square section)7207.11.005%AFree from day one
Hot-rolled non-alloy steel in coils, under 3 mm thick7208.39.005%AFree from day one
Hot-rolled non-alloy steel plate, not in coils, over 10 mm thick7208.51.005%AFree from day one
Refined copper cathodes7403.11.005%AFree from day one
Unwrought nickel, not alloyed7502.10.005%AFree from day one
Aluminium waste and scrap7602.00.005%AFree from day one
Hollow profiles of aluminium alloy7604.21.005%AFree from day one
Aluminium alloy plates and sheets, over 0.2 mm and up to 8 mm thick7606.12.105%AFree from day one
Aluminium doors, windows and their frames, other than powered garage doors7610.10.905%AFree from day one
Gas-fuelled cookers of iron or steel7321.11.105%AFree from day one

04Metals phased in over four or six years

Thirty-six metal lines without an asterisk lose their duty in yearly steps. Seven take four years and 29 take six years. They are mostly oil and gas pipe, copper and nickel semi-finished goods, and some aluminium products.

ProductUAE tariff codeDuty todayCategoryWhat happens
Wire of brass (copper-zinc alloy)7408.21.005%BFree on 1 January of year four
Bars, rods and profiles of nickel, not alloyed7505.11.005%BFree on 1 January of year four
Plates, sheets, strip and foil of nickel alloy7506.20.005%BFree on 1 January of year four
Venetian blinds of aluminium7616.99.405%BFree on 1 January of year four
Seamless line pipe for oil or gas pipelines, not stainless7304.19.005%CFree on 1 January of year six
Seamless casing and tubing for oil or gas drilling, not stainless7304.29.005%CFree on 1 January of year six
Steel structures and parts of structures, other kinds7308.90.905%CFree on 1 January of year six
Refined copper in other unwrought forms7403.19.005%CFree on 1 January of year six
Copper waste and scrap7404.00.005%CFree on 1 January of year six
Bars, rods and solid profiles of aluminium alloy7604.29.005%CFree on 1 January of year six
Aluminium tube and pipe fittings7609.00.005%CFree on 1 January of year six
Aluminium containers for compressed or liquefied gas, other than small gas cylinders7613.00.905%CFree on 1 January of year six

05Metals left out of the agreement

Ten lines of steel articles are in category E. The UAE makes no tariff promise on them, so Canadian goods under these lines keep paying the UAE's general duty, which is 5% today.

ProductUAE tariff codeDuty todayCategoryWhat happens
Seamless casing and tubing for oil or gas drilling, of stainless steel7304.24.005%ENot covered by a cut. The UAE's general duty applies (5% today)
Other seamless tubes of alloy steel, round, not cold-drawn7304.59.005%ENot covered by a cut. The UAE's general duty applies (5% today)
Cast pipe fittings of non-malleable cast iron7307.11.005%ENot covered by a cut. The UAE's general duty applies (5% today)
Screws and bolts, other kinds, with or without nuts and washers7318.15.005%ENot covered by a cut. The UAE's general duty applies (5% today)
Nuts7318.16.005%ENot covered by a cut. The UAE's general duty applies (5% today)
Other non-threaded fasteners7318.29.005%ENot covered by a cut. The UAE's general duty applies (5% today)
Helical springs7320.20.005%ENot covered by a cut. The UAE's general duty applies (5% today)
Other sanitary ware of iron or steel, including parts7324.90.005%ENot covered by a cut. The UAE's general duty applies (5% today)
Tent pegs and stakes for tethering livestock7326.90.805%ENot covered by a cut. The UAE's general duty applies (5% today)
Rabbit and poultry cages, hives, animal feeders and drinkers, and ploughs7326.90.985%ENot covered by a cut. The UAE's general duty applies (5% today)
  • Category E lines are outside the duty-cutting article altogether. The agreement sets no timetable for them.
  • Either country can ask for talks on widening or speeding up the cuts. An agreed change takes effect once both countries have approved it. Either country may also speed up or widen its own cuts on its own, without the other's approval.

06The asterisk lines: 237 cuts on hold

For 237 metal lines the UAE's tariff cut is suspended. Canadian goods under these lines keep paying the present 5% or 10% after the agreement takes effect. The hold lasts until 30 days after Canada tells the UAE in writing that it no longer keeps a surtax on UAE goods under the marked lines.

  • What is on hold: the UAE's promise to cut the duty, and its promise not to raise it. Both come from the same article of the agreement, and that article is switched off for these lines.
  • What ends the hold: a written notice from Canada to the UAE saying that Canada no longer keeps a surtax on UAE goods under the marked lines, and that the UAE's duty cuts can now apply to all of them. A surtax is an extra import charge on top of the normal duty.
  • When the cuts start: 30 days after that notice. Lines marked A* become duty free at that point. Lines marked B* start their four yearly steps from that point, not from the day the agreement took effect.
  • No date is set. The agreement does not say when Canada will send the notice, and it does not name the surtax.
  • Talks are possible. Either country can ask the joint Committee on Trade in Goods to meet about the marked lines, including to discuss removing the duties.

Where the 237 asterisks fall

Product groupHeadingsAsterisk lines
Cold-rolled and coated flat steel72.09 to 72.1224
Bars and rods of non-alloy steel (10% duty)72.13 to 72.1523
Angles, shapes and sections72.1613
Wire of non-alloy steel72.173
Stainless steel72.18 to 72.2320
Other alloy steel, including alloy bars at 10% duty72.25 to 72.2829
Sheet piling and railway track material73.01 to 73.025
Tubes, pipes and pipe fittings73.03 to 73.0733
Structures, tanks, drums and gas cylinders73.08 to 73.1121
Wire rope, fencing, chain, nails, fasteners, springs73.12 to 73.2035
Radiators, household and sanitary articles73.22 to 73.2411
Cast and other articles of iron or steel73.25 to 73.2618
Unwrought aluminium, alloyed and not alloyed76.012
  • Of the 237 lines, 196 are marked A* and 41 are marked B*.
  • Of the 47 steel lines at 10% duty, 46 carry an asterisk. The exception is 7214.20.40, ribbed bars of 10 to 32 mm diameter, which is in category A without an asterisk and becomes duty free on day one.
  • No copper or nickel line carries an asterisk.
  • Across the whole UAE schedule there are 305 asterisk lines. Metals account for 237 of them.

Examples

ProductUAE tariff codeDuty todayCategoryWhat happens
Unwrought aluminium, not alloyed7601.10.005%A*On hold. Free once Canada lifts its surtax
Unwrought aluminium alloys7601.20.005%A*On hold. Free once Canada lifts its surtax
Hot-rolled bars and rods in coils, with ribs or grooves from rolling7213.10.0010%A*On hold. Free once Canada lifts its surtax
Other hot-rolled bars with ribs or grooves, other sizes7214.20.9010%A*On hold. Free once Canada lifts its surtax
Flat-rolled steel, painted, varnished or coated with plastics7210.70.005%A*On hold. Free once Canada lifts its surtax
U, I or H sections under 80 mm high7216.10.005%A*On hold. Free once Canada lifts its surtax
Stainless steel wire7223.00.005%A*On hold. Free once Canada lifts its surtax
Seamless drill pipe, not stainless7304.23.005%A*On hold. Free once Canada lifts its surtax
Large-diameter casing for oil or gas drilling7305.20.005%A*On hold. Free once Canada lifts its surtax
Steel bridges and bridge sections7308.10.005%A*On hold. Free once Canada lifts its surtax
Steel nails and carpentry nails7317.00.105%A*On hold. Free once Canada lifts its surtax
Zinc-coated (galvanised) flat-rolled steel, not corrugated7210.49.005%B*On hold. Then four yearly cuts to zero
Other alloy steel bars, hot-rolled, other sizes7228.30.9010%B*On hold. Then four yearly cuts to zero
Welded round tubes of alloy steel other than stainless7306.50.005%B*On hold. Then four yearly cuts to zero
Steel towers and lattice masts7308.20.005%B*On hold. Then four yearly cuts to zero
Stainless steel flanges7307.21.005%B*On hold. Then four yearly cuts to zero
Self-tapping screws7318.14.005%B*On hold. Then four yearly cuts to zero

07Rules of origin for metals

A metal product gets the CEPA duty only if it counts as Canadian. Metal that is mined, smelted or recovered as scrap in Canada qualifies. Where imported inputs are used, the usual test is that the input falls under a different four-digit tariff heading from the finished product.

  • Iron and steel (Chapter 72): one rule for every heading. Imported inputs must come from another heading. Hot-rolled coil (heading 72.08) rolled in Canada from imported slab (heading 72.07) meets the test. Imported coil that is only cut to length stays in heading 72.08 and does not.
  • Steel articles (Chapter 73): mostly the same test as for Chapter 72. Imported inputs must come from another heading. For structures (73.08), chain parts (7315.19 and 7315.90), anchors (73.16), leaf springs (7320.10), stoves (73.21), radiators (73.22), household articles (73.23) and sanitary ware (73.24) there is a second route. The good also qualifies if imported materials of that same heading are worth no more than 60% of its ex-works price, which is the price paid to the producer at the factory.
  • Cold-drawn seamless stainless steel tubes (7304.41): it is enough that imported inputs come from a different six-digit subheading.
  • Copper (Chapter 74): change of heading for headings 74.01 to 74.15. Household copper articles (74.18) and other copper articles (7419.80) also have the 60% route.
  • Nickel (Chapter 75): change of heading for most goods. Nickel wire (7505.21 and 7505.22) can also be drawn from imported nickel bar or rod if the cross-section is reduced by at least 50%.
  • Aluminium (Chapter 76): change of heading for unwrought metal, scrap, powders, bars and profiles, plate and sheet, tubes and structures. Wire (76.05) and foil (76.07) need only a change of subheading. Stranded wire and cables (76.14) and household articles (76.15) also have the 60% route.
  • Small-amount allowance: a good that fails the heading test still qualifies if all the materials in it that are neither Canadian nor from the UAE are together worth no more than 15% of the good's ex-works price.
  • UAE inputs count: materials that qualify as UAE goods are treated as Canadian when used in Canadian production.
  • What does not count: a good does not become Canadian only because it was taken apart, repackaged or given a different end use.
  • Scrap: waste and scrap from production in Canada, or from used goods collected in Canada and fit only for recovering raw materials, counts as wholly Canadian.

The certificate of origin and the full origin test are explained on the rules of origin page.

08What Canada does on UAE metals

Canada also lists 233 of its 433 metal lines with an asterisk, covering steel, steel articles and aluminium. On those lines Canada's tariff promises are on hold too, although the agreement says the hold does not touch Canada's ordinary duty rates, the rates it charges World Trade Organization members with which it has no trade agreement. Canada currently applies surtaxes to steel imports, described below.

  • Canada's schedule for Chapters 72 to 76: 433 lines. 421 are in category A and 12 in category C.
  • Asterisks: 135 lines in iron and steel (Chapter 72), 78 in steel articles (Chapter 73) and 20 in aluminium (Chapter 76).
  • In practice: Canada's schedule already lists most of the marked lines as "Free", including unwrought aluminium. What the asterisk leaves open is Canada's surtax.
  • Copper and nickel: all 80 Canadian lines are in category A with no asterisk.
  • Six-year lines include: non-electric cooking stoves of iron or steel (7% and 8% today), skid chain (6%) and articles of steel wire (6.5%).
  • UAE goods need a certificate of origin issued by the UAE's competent authority, or by another method the two countries agree, to claim Canada's CEPA rates.

Canada's steel surtaxes today

  • Canada sets quotas on steel imports from countries other than the United States and Mexico. Steel above the quota pays a 50% surtax. Since 26 December 2025 the quota for countries without a free trade agreement in force with Canada is 20% of 2024 import levels. For listed free trade partners it is 75%.
  • Since 26 December 2025 Canada also charges 25% on the full value of listed goods made from steel (called steel derivative products) from any country.
  • The agreement does not say which Canadian surtax the asterisk refers to, and it does not say how the UAE will be treated under the quotas once the CEPA is in force.

What changed

  • 27 October 2026Canada and the UAE signed the CEPA in Ottawa. It has not yet entered into force.
  • 24 July 2026Canada and the UAE concluded the CEPA negotiations.
  • 26 December 2025Canada tightened its steel import quotas and began charging 25% on listed steel derivative products from all countries.
  • 1 January 2025Reference date for the base rates in both tariff schedules.

This page is general information, not legal or tax advice.

© 2026 NordGulf Alliance FZE LLC. You may read, share and quote this page free of charge, with credit to the NordGulf Institute. It may not be sold, resold or republished for commercial use without our written permission.

© 2026 NordGulf Alliance · All Rights Reserved

Norway · Sweden · Finland · Denmark · UAE · KSA · Switzerland

Nordgulf Alliance FZE LLC  ·  Licensed by Sharjah Publishing City Free Zone Authority  ·  Registration No. 4422720

Business Centre, Sharjah Publishing City Free Zone, Sharjah, United Arab Emirates

© 2026 NordGulf Alliance. All rights reserved.

Privacy and cookies